Blastbot - Remote Control for Air Heat Pump

SKU: BCD01
Brand:
Unit: pcs
Qty: 33
Price:
89,90 €
Qty.: - +
   - or -   
All your controls in one app
Install Blastbot in your room and control all your electronic devices at anywhere using your smartphone.

Blastbot makes your days easier

A solution that adapts to your needs. Connect it to any of your infrared transmission devices and customize your controls.



Technical characteristics



 
Connection Wi-FI
Indicator light LED
Color Black
Size and weight High: 2.12 cm
Wide: 8.12 cm
Long: 6.68 cm
Weight: 100 g
Included in box 1 SmartControl
1 Micro USB Cable
1 5V power adapter
Warranty
Manual
Warranty 1 year with the manufacturer
Similar products
The Danfoss temperature sensor is used for central temperature detection and heating/cooling system control, also with multiple thermostats. The measured temperature is displayed. Two front buttons allow to overwrite the target temperature. The overwrite can be terminated for certain hours. After this time the setpoint temperature will go back to the redefined value. The device can be used as Z-Wave stand alone temperature sensor, too.
SKU: 014G0160 ,   Qty: Tellimisel
106,28 €
Additional temperature sensor for Heatit thermostats. 10Kohm. Needs wiring.
SKU: 5430128-TF026 ,   Qty: 2
38,40 €
The LC-13 by Danfoss is a Z-Wave controlled electronic radiator thermostat. It is applied to be mounted on wall heating valves and controls them by a motor. The device accepts a set point that is either set manually using local buttons on the device or wirelessly using Z-Wave. Beside setting a desired temperature the device will support special heating schemes, such as energy saving and frost protection. A small LCD display on the device shows the target temperature on request.

The device owns further intelligent functions such as detection of open windows or a valve training function to ensure that valves are still operational after longer periods.

The Danfoss LC-13 thermostat can be mounted with few movements to valves with standard M30x1.5 connector or RA2000 (Danfoss snap in). The device expects a regular radio connection to the IP gateway for status message exchange.
SKU: 014G0013 ,   Qty: 3
64,80 €
Product information "TKB Thermostat for Floor heating"
The TKBETZ1036 is a heating thermostat with LCD screen and built-in Z-Wave technology. The thermostat is designed to fit into your flush box and control your electric heating or on/off actuator valves used in hydronic heating. The thermostat is mains powered and has an internal temperature sensor built in and an external sensor included in the scope of delivery. To use both sensors you have to connect the external sensor to the thermostat. Then the thermostat allows to switch between the 2 different sensors. The display shows the value of the chosen temperature sensor and allows adjusting the temperature of the connected heating system. The temperature can be adjusted in steps of 1° C.
SKU: TKBETZ1036 ,   Qty: Tellimisel
70,00 €
Heatit Z-TRM2fx is an electronic thermostat for electrical floor heating. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems like Fibaro, Futurehome, Smarthings, Homeseer, Vera, Zipato etc.

Heatit Z-TRM2fx is equipped with a single pole switch and it fits most System 55 frames (Elko RS16, Schneider Exxact, Gira, Jung etc.). The thermostat can withstand a load of max 13A /2900W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors.

The thermostat has the capacity of up to 5 associations (relays, wall plugs etc.).
SKU: 5430560 ,   Qty: 4
139,00 €