Heatit Z-TRM2fx thermostat Z-Wave

SKU: 5430560
Brand:
Unit: pcs
Qty: 4
Price:
139,00 €

Parameters


* Color

Qty.: - +
   - or -   
Heatit Z-TRM2fx is an electronic thermostat for electrical floor heating. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems like Fibaro, Futurehome, Smarthings, Homeseer, Vera, Zipato etc.

Heatit Z-TRM2fx is equipped with a single pole switch and it fits most System 55 frames (Elko RS16, Schneider Exxact, Gira, Jung etc.). The thermostat can withstand a load of max 13A /2900W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors.

The thermostat has the capacity of up to 5 associations (relays, wall plugs etc.).
Heatit Z-TRM2 is an electronic thermostat for electrical floor heating. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems like Fibaro, Futurehome, Smarthings, Homeseer, Vera, Zipato etc.
 
Heatit Z-TRM2 is equipped with a single pole switch and it fits most System 55 frames (Elko RS16, Schneider Exxact, Gira, Jung etc.). The thermostat can withstand a load of max 13A /2900W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors.
 
The thermostat has the capacity of up to 8 associations (relays, wall plugs etc.).
 
The thermostat is designed for electrical heating and to be used with floor sensor or external room sensor.
FEATURES
  • Floor sensor
  • External room sensor
  • Temperature limiter
  • Weekly program/setback via gateway or pilot wire
  • Multilevel sensor command class
  • Firmware updates (OTA)
  • Power metering
  • LED-diode
  • Can be used in connection with different NTC-sensors
  • Lock mode/child lock
  • Calibration
  • 8 associations
  • Supports encryption mode: S0, S2 Authenticated Class, S2 Unauthenticated Class
TECHNICAL DATA
Protocol Z-Wave 
SDK 6.71.00
Rated voltage 230V 50/60Hz
Max load 2900W (resistive load)
750W self-limiting heating cable
Max current 13A
Power consumption <2,0W
Min/max installation temp -20°C – 40°C
Min/max operating temp 5°C – 40°C
Temperature intervals Floor sensor 5°C – 40°C
External room sensor 5°C – 40°C
Hysteresis 0,3°C – 3,0°C (default 0,5°C)
Switch Single-pole switch
Included in package Floor sensor, Art. no. 54 301 07
Compatible with NTC
sensors with values
 10, 12, 15, 22, 33 and 47 kΩ @ 25°C
IP Class IP 21
Approvals Z-Wave Plus, CE, EN 60730-1, EN 60730-2-9, EMC 2014/30/EU, RoHS 2011/65/EU, LVD 2014/35/EU
Terminal Use 1,5mm² or 2,5mm² according to load.
Similar products
MCOHome Water / Electrical Heating Thermostat is a Z-Wave enabled device for indoor temperature control. MH7-WH-EU is mainly applied to control wall mounted boiler, water
valve/pump etc. , while MH7-EH-EU for electrical heating system. The device is of high reliability and practicability. And can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers.
SKU: MH7H-WH ,   Qty: Tellimisel
153,99 €
External room sensor, glass front NTC 10 k?
SKU: 5430108 ,   Qty: Tellimisel
25,20 €
The LC-13 by Danfoss is a Z-Wave controlled electronic radiator thermostat. It is applied to be mounted on wall heating valves and controls them by a motor. The device accepts a set point that is either set manually using local buttons on the device or wirelessly using Z-Wave. Beside setting a desired temperature the device will support special heating schemes, such as energy saving and frost protection. A small LCD display on the device shows the target temperature on request.

The device owns further intelligent functions such as detection of open windows or a valve training function to ensure that valves are still operational after longer periods.

The Danfoss LC-13 thermostat can be mounted with few movements to valves with standard M30x1.5 connector or RA2000 (Danfoss snap in). The device expects a regular radio connection to the IP gateway for status message exchange.
SKU: 014G0013 ,   Qty: 3
64,80 €
Heatit Extra floor sensor for Z-Water or Heatit thermostat.
SKU: 5430107 ,   Qty: Tellimisel
9,00 €
The MCOEMH8-FC4 thermostat is a device for room temperature control, equipped with Z-Wave wireless technology. It is destined for central control of a 4-pipe fan coil, which influences room climate by heating, cooling, humidify and dehumidify. The device can read room temperature and local time, and automatically control fan speed based on the temperature difference.

The wall thermostat MCOEMH8-FC4 requires a static installation with mains power. Thanks to its modern design with capacitive glass touch panel it is particularly suited for visible installation in living areas.

With the modern designed glass touch thermostats by MCO you can control various heating and cooling systems – e.g. heating cable, heating film, water valve, electrical valve, boiler, fan coil, solar energy controller, heat pump, ventilation system etc,
SKU: MCOEMH8-FC4 ,   Qty: Tellimisel
149,99 €